Academic Journal
USE OF MICROWAVE RADIATION FOR SEPARATION OF LIQUID GLASS HEAT INSULATION MATERIALS
| Τίτλος: | USE OF MICROWAVE RADIATION FOR SEPARATION OF LIQUID GLASS HEAT INSULATION MATERIALS |
|---|---|
| Πηγή: | Collection of Scientific Works of the Ukrainian State University of Railway Transport; No. 193 (2020): Collected scientific works of Ukrainian state university of railway transport Сборник научных статей Украинского государственного университета железнодорожного транспорта; № 193 (2020): Збірник наукових праць Українського державного університету залізничного транспорту Збірник наукових праць Українського державного університету залізничного транспорту; № 193 (2020): Збірник наукових праць Українського державного університету залізничного транспорту |
| Στοιχεία εκδότη: | Ukranian State University of Railway Transport, 2020. |
| Έτος έκδοσης: | 2020 |
| Θεματικοί όροι: | heat-insulating materials, liquid glass, microwave radiation, monolithic treatment, liquid glass granules, binder, теплоізоляційні матеріали, рідке скло, НВЧ випромінювання, омонолічування, рідкоскляні гранули, зв'язуюче, 7. Clean energy |
| Περιγραφή: | The study of the thermal insulation market of Ukraine showed that the market is dominated by aerated concrete and silicates, which are used as thermal insulation materials at an average density of 300-500 kg / m3. Their disadvantages include high values of water absorption and hygroscopicity, as well as very low flexural strength, because this material does not have elasticity and the use of small bending forces leads to its cracking. Foam glass has a set of operational properties that meet the highest regulatory requirements. Foam glass is the strongest of all effective thermal insulation materials, but this material is fragile. It is sensitive to vibration - induced damage. In addition, the technology of production of foam glass is quite complex and requires high energy consumption, as a consequence, the cost of this material is high. Therefore, it was important to develop thermal insulation material with the appropriate level of performance while reducing production costs. This was achieved by using energy-saving microwave technology to swell liquid glass materials. This technology is based on the simultaneous swelling of the liquid glass granulate and the binder under microwave radiation, which, due to the volumetric heating of the liquid glass composition, allows to obtain a strong monolithic material with a rigid, homogeneous and mostly closed-porous structure. The production of thermal insulation materials is proposed to be carried out on the basis of liquid glass granulate, because the introduction of granules reduces the deformability and shrinkage of the material and prevents its cracking, increases its strength, because the granular material has a certain plastic deformation, reduces water hygroscopicity. granules swell to form a compacted shell, which slows down the absorption kinetics of water and its vapor. The monolithic granules are proposed to be carried out with a binder that foams not only due to the release of water, but also with the help of a gasifier, because this technology will allow uniform distribution of the binder in the intergranular space, thus forming a more homogeneous structure of the material, which has a positive effect on its physical and mechanical characteristics. Дослiдження ринку теплоiзоляцiї України показало, що переважають на цьому ринку ніздрюваті бетони і силікати, які застосовують як теплоізоляційні матеріали при середній щільності 300–500 кг/м3. До їх недоліків відносять великі значення водопоглинання і гігроскопічності, а також дуже низьку міцність на вигин, оскільки такий матеріал не володіє еластичністю і застосування невеликих згинальних зусиль призводить до його розтріскування. Комплексом експлуатаційних властивостей, що відповідають найвищим нормативним вимогам, володіє піноскло. Піноскло – найміцніший з усіх ефективних теплоізоляційних матеріалів, однак цей матеріал є крихким. Він чутливий до вібраційно-індукованих пошкоджень. До того ж технологія виробництва піноскла досить складна і потребує високих енерговитрат, як наслідок, вартість цього матеріалу висока. Тому актуальним було розробити теплоізоляційний матеріал з відповідним рівнем експлуатаційних властивостей при зниженні витрат на виробництво. Досягти цього вдалося застосуванням енергоощадної технології НВЧ спучування рідкоскляних матеріалів. Ця технологія базується на одночасному спучуванні рідкоскляного грануляту та зв’язуючого в умовах НВЧ випромінювання, яке завдяки об'ємному прогріву рідкоскляної композиції дає змогу отримати міцний омонолічений матеріал з жорсткою, однорідною та переважно закритопористою структурою. |
| Τύπος εγγράφου: | Article |
| Περιγραφή αρχείου: | application/pdf |
| Γλώσσα: | Ukrainian |
| ISSN: | 1994-7852 2413-3795 |
| Σύνδεσμος πρόσβασης: | http://csw.kart.edu.ua/article/view/229526 |
| Rights: | CC BY NC ND |
| Αριθμός Καταχώρησης: | edsair.scientific.p..d6f6b64b87187d62a57fca02a2920aaa |
| Βάση Δεδομένων: | OpenAIRE |
| ISSN: | 19947852 24133795 |
|---|