Academic Journal
Формувальна обробка металевих пластин та дисків локальним лазерним нагріванням
| Τίτλος: | Формувальна обробка металевих пластин та дисків локальним лазерним нагріванням |
|---|---|
| Πηγή: | Eastern-European Journal of Enterprise Technologies; Том 3, № 5(63) (2013): The applied physics and materials technology; 19-22 Восточно-Европейский журнал передовых технологий; Том 3, № 5(63) (2013): Прикладная физика и материаловедение; 19-22 Східно-Європейський журнал передових технологій; Том 3, № 5(63) (2013): Прикладна фізика та матеріалознавство; 19-22 |
| Στοιχεία εκδότη: | PRIVAT COMPANY "TECHNOLOGY CENTER", 2013. |
| Έτος έκδοσης: | 2013 |
| Θεματικοί όροι: | 0211 other engineering and technologies, 0202 electrical engineering, electronic engineering, information engineering, Лазерне формоутворення, листові матеріали, деформація, теплові способи формоутворення, зона термічного впливу, Лазерное формирование, листовые материалы, деформация, тепловые способы формообразования, зона термического влияния, 02 engineering and technology, УДК 621.9.04, Laser forming, plate materials, deformation, thermal method of forming, heat-affected zone |
| Περιγραφή: | The article is devoted to the study of thermal methods of forming. Namely, the laser forming, as the laser as a thermal source is stable, well defined, bases easily, and provides a locality heating. The mechanisms of laser forming were analyzed. The results of experimental studies were presented. It was found that the amount of deformation is proportional to the number of irradiation cycles for both carbon and austenitic stainless steels. When processing carbon steels the "post-deformation" occurs. It may or may not be coincident with the direction of the main deformation. The resistance of the laser formed constructions was studied. It was shown that the resistance of the constructions formed with the laser to force and thermal load is higher than of the constructions formed by the pressure treatment.This is explained by the fact that the pressure treatment in the processing zone causes wall thinning of an item, in turn, the laser forming causes the reverse process - thickening. Technological recommendations on the treatment of metal plates were worked out. The results of the forming of items of complex spatial configuration with the irradiation by the parallel and cross laser passages were presented.It was found that during the irradiation along the curvilinear trajectories it is appropriate to use a uniform heating, which can be achieved by rotating a workpiece with a frequency of 11000 rotations in a minute. The uniform heating of the workpiece in a closed curvilinear contour allows a uniform distribution of stresses and strains Проаналізовані механізми лазерного формоутворення, найбільш дослідженим та найбільш ефективним являється механізм градієнту температур. Приведені результати експериментальних досліджень. Величина деформації прямо пропорційна до кількості формувальних проходів, як у випадку обробки вуглецевих сталей, так і при обробці нержавіючих сталей аустенітного класу Проанализированы механизмы лазерного формирования. Приведены результаты экспериментальных исследований. Величина деформации прямо-пропорциональна количеству формирующих проходов, как в случае обработки углеродистых сталей, так и в случае обработки нержавеющих сталей аустенитного класса |
| Τύπος εγγράφου: | Article |
| Περιγραφή αρχείου: | application/pdf |
| Γλώσσα: | Ukrainian |
| ISSN: | 1729-3774 1729-4061 |
| Σύνδεσμος πρόσβασης: | http://journals.uran.ua/eejet/article/view/14484 |
| Rights: | CC BY |
| Αριθμός Καταχώρησης: | edsair.scientific.p..9b5da7d00ebd49f9fb0be7223d408ef6 |
| Βάση Δεδομένων: | OpenAIRE |
| ISSN: | 17293774 17294061 |
|---|