Academic Journal
Analysis of the influence of the estimate of standard measurement uncertainty as a result of a correction due to the finite resolution of the readings on the decision on the measuring equipment conformity during calibration
| Title: | Analysis of the influence of the estimate of standard measurement uncertainty as a result of a correction due to the finite resolution of the readings on the decision on the measuring equipment conformity during calibration |
|---|---|
| Source: | Ukrainian Metrological Journal; No. 3 (2025); 3-10 Украинский метрологический журнал / Ukrainian Metrological Journal; № 3 (2025); 3-10 Український метрологічний журнал / Ukrainian Metrological Journal; № 3 (2025); 3-10 |
| Publisher Information: | National Scientific Centre "Institute of Metrology", 2025. |
| Publication Year: | 2025 |
| Subject Terms: | measurement uncertainty, maximum permissible error, measuring equipment, measurement uniformity, calibration, metrological confirmation, calibration procedure, невизначеність вимірювань, максимально допустима похибка, вимірювальне обладнання, єдність вимірювань, калібрування, метрологічне підтверджування, методика калібрування |
| Description: | The paper considers the features of the evaluation of the component of standard measurement uncertainty of type B as a result of a correction due to the finite resolution of the readings of measuring equipment during calibration. The problem of carrying out the procedure for establishing the compliance of the measuring equipment with the technical specification based on the results of its calibration is stated. It is emphasized that the procedure shall necessarily account for the measurement uncertainty. In this regard, the metrological characteristics of the measuring equipment after calibration may not meet the requirements of the technical specification. The calibration and measurement capabilities of accredited laboratories when calibrating a smooth micrometer MK25 for compliance with the technical specification according to the results of its calibrations are analysed. It is shown that the component of standard measurement uncertainty of type B as a result of a correction due to the resolution of the readings of analogue measuring instruments cannot be dominant in the uncertainty budget. It is proposed to consider the establishment of a target uncertainty during calibration for the analysis of the calibration and measurement capabilities of measuring equipment in the laboratory. At the same time, the reliability of the evaluation of measurement uncertainty during the calibration of measuring equipment depends on the correct choice of appropriate procedures. Therefore, at the legislative level, namely in the Law of Ukraine “On Metrology and Metrological Activities”, it is established that the measurement equipment results are calibrated and registered in accordance with national standards harmonized with relevant international and European standards, and documents approved by international and regional metrology organizations. У статті розглянуто особливості оцінювання складової стандартної невизначеності за типом В, що обумовлена поправкою через кінцеву роздільну здатність показань вимірювального обладнання при калібруванні. Зазначено проблему проведення процедури встановлення відповідності вимірювального обладнання технічній специфікації за результатами його калібрування. Зроблено наголос, що процедура встановлення відповідності вимірювального обладнання при калібруванні обов’язково має враховувати невизначеність вимірювань. У зв’язку з цим метрологічні характеристики вимірювального обладнання після калібрування можуть не відповідати вимогам технічної специфікації. Проведено аналіз калібрувальних та вимірювальних можливостей акредитованих лабораторій при калібруванні мікрометра гладкого МК25 щодо відповідності технічній специфікації за результатами його калібрування. Показано, що складова стандартної невизначеності за типом В, що обумовлена поправкою через кінцеву роздільну здатність показань аналогових засобів вимірювальної техніки, не може бути домінуючою в бюджеті невизначеності. Запропоновано для аналізу калібрувальних та вимірювальних можливостей калібрування вимірювального обладнання лабораторії зважати на встановлення цільової невизначеності при калібруванні. При цьому достовірність оцінки невизначеності вимірювань під час калібрування вимірювального обладнання залежить від правильного вибору процедур оцінювання невизначеності вимірювань при калібруванні. Тому на законодавчому рівні, а саме в Законі України “Про метрологію та метрологічну діяльність”, встановлено, що калібрування та оформлення його результатів проводяться відповідно до національних стандартів, гармонізованих з відповідними міжнародними та європейськими стандартами, та документів, прийнятих міжнародними та регіональними організаціями з метрології. |
| Document Type: | Article |
| File Description: | application/pdf |
| Language: | Ukrainian |
| ISSN: | 2306-7039 2522-1345 |
| Access URL: | http://umj.metrology.kharkov.ua/article/view/340414 |
| Accession Number: | edsair.scientific.p..cb971b9e51b4552a18c7b17a3a08b44d |
| Database: | OpenAIRE |
| ISSN: | 23067039 25221345 |
|---|